{"product_id":"c-stand_transp_mt_prin","title":"C-Stand Transport Mounts (printable, free)","description":"\u003cp\u003eSimply clip your C-Stand(s) to the shelves of your SCHLEPP ONE or SCHLEPP ONE-S Camera cart for transport!\u003c\/p\u003e\n\u003cp\u003eMounts stay bolted to the pole of your C-Stand. \u003c\/p\u003e\n\u003cp\u003eThis printable C-Stand transport holder for SCHLEPP ONE Camera Cart consists of two printable parts and some fasteners (widely available).\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e1. printable parts (free for download)\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eYou can get the STL-file for the upper and lower part of the C-Stand transport holder here:\u003c\/p\u003e\n\u003cp\u003e\u003ca rel=\"noopener\" title=\"Printable C-Stand Transport Mount\" href=\"https:\/\/www.printables.com\/model\/1627523-c-stand-transport-mounts-for-schlepp-one-camera-ca\" target=\"_blank\"\u003e\u003cspan\u003eDOWNLOAD for free on printables.com\u003c\/span\u003e\u003c\/a\u003e\u003ca rel=\"noopener\" title=\"Printable Boom Pole Holder\" href=\"https:\/\/www.printables.com\/model\/1605071-boompole-holder-for-schlepp-one-camera-cart\" target=\"_blank\"\u003e\u003cspan\u003e\u003c\/span\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.printables.com\/@SCHLEPP_Came_3161740\"\u003e\u003cspan\u003eSCHLEPP Camera Carts on printables.com\u003c\/span\u003e\u003c\/a\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e2. Required Fasteners:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003e4x M6x 55mm HEX Screw\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003e4x M6 Nuts \u003c\/em\u003e\u003cem\u003e(+10mm Wrench)\u003c\/em\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cem\u003e4x M6 Washers\u003c\/em\u003e\u003cem\u003e\u003c\/em\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eOrientation: \u003cstrong\u003ePrint 45° upright for optimized part stability\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eRecommended filament: PETG, ABS, PA6, PA12 - do not use abrasive (reinforced) filaments as those may scratch the coating when placing and removing C-Stands to the shelves' lips. \u003c\/p\u003e\n\u003cp\u003eInstructions:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cp\u003eClip printed mounts onto the C-Stand pole. The closed side of the mount should point towards the direction of the folded C-Stand feet. (Side with screws should point towards the 180° opposite of the folded C-Stand feet). The lower mount is 9mm deeper to fit onto the lip (wall) of the middle shelf.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eM6x55 Hex screws are inserted from the rear sides of the parts - into the hexagonal holes.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eDetermine the right height \/ distance by placing the C-Stand with the printed mounts (clipped on) onto the top shelf and middle shelf of your SCHLEPP Camera Cart.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eMount the (printed) upper part flush against the bottom of the \u003cstrong\u003elowest locking joint of the C-Stand\u003c\/strong\u003e; this ensures the joint sits on the mount and \u003cstrong\u003emechanically blocks \u003c\/strong\u003eany downward movement.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eStart with upper mount: apply washers and nuts from the front side of the printed mounts - tighten them carefully (10mm wrench required) ! Too much force will brake any printed parts! \u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eTighten nuts on lower mount carefully. \u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eThe mounts can be used on the (long) front or (long) rear side of your shelves. You can clip up to 4 C-Stands to your SCHLEPP Camera Cart, with the folded C-Stand legs pointing outwards.\u003c\/p\u003e\n\u003cp\u003eFor setups using two C-stands on the same side, print a \u003cstrong\u003emirrored version\u003c\/strong\u003e of both the upper and lower mounts. This can be done effortlessly using the \u003cstrong\u003emirror function\u003c\/strong\u003e in most slicing software.\u003c\/p\u003e\n\u003cp\u003eUsing more than one C-Stand may require counterweight on your base.\u003c\/p\u003e\n\u003cp\u003e⚠  Please check, if your setup is stable in operation (while pushing \/ pulling \/ turning) before adding expensive gear. If required, add counterweight to the base shelf.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWe assume no liability for the operation, for the stability and \/ or functionality, as the stability of the part is highly dependent on your print quality and how it is used.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e","brand":"SCHLEPP Camera Carts by rent one","offers":[{"title":"Default Title","offer_id":56910287700300,"sku":"CSM-print","price":0.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0854\/1801\/7100\/files\/C-Stand_Transport-2._001.jpg?v=1772807924","url":"https:\/\/schleppcarts.com\/products\/c-stand_transp_mt_prin","provider":"SCHLEPP Camera Carts by rent one","version":"1.0","type":"link"}